Description

Analog Inputs - Connections: XLR and 6.3-mm jack - Input type: RF-filtered, servo-balanced - Impedance: 50 kOhm balanced, 25 kOhm unbalanced - Maximum input level: +21 dBu, balanced and unbalanced - CMRR: typically 40 dB, >55 dB at 1 kHz Analog Outputs - Connections: XLR and 6.3-mm jack - Output stage: electronically controlled and servo-balanced - Impedance: 60 Ohm balanced, 30 Ohm unbalanced - Maximum output level: +16 dBu, balanced and unbalanced System Data - Frequency range: 20 Hz to 20 kHz, ±0.5 dB - Signal-to-noise ratio: >103 dB, unweighted, 22 Hz to 22 kHz - THD: typically 0.004 % at +4 dBu, 1 kHz and gain 1 - Crosstalk: < -103 dB, 22 Hz to 22 kHz Bypass - Relay-based bypass; a hard bypass is activated in the event of a power failure Measurement Microphone Input - Input type: servo-balanced - Input impedance: 2 kOhm - Nominal input level: -60 dBu to 0 dBu - Maximum input level: +1 dBu - Phantom power: +15 V Digital Input (optional) - Format: AES/EBU, transformer-balanced - Input impedance: 10 kOhm balanced - Nominal input level: 3–10 V Peak-to-Peak Digital Output (optional) - Format: AES/EBU, transformer-balanced - Output impedance: 100 Ohm balanced - Output level: 5 V Peak-to-Peak MIDI Interface - Connections: 5-pin DIN sockets for In, Out and Thru - The implementation can be found in the MIDI implementation chart Digital Signal Processing - Converters: 24-bit sigma-delta - Sample rates: 48 kHz and 44.1 kHz; with AES/EBU option additionally 32 kHz Graphic Equalizer (GEQ) - Digital third-octave equalizer - 31 third-octave bands from 20 Hz to 20 kHz at standardized ISO frequencies - Bandwidth: 1/3 octave - Control range: +16 to -16 dB - Adjustment increments: 0.5 dB at True Response Parametric Equalizer (PEQ) - Three independent, fully parametric filters per channel - Alternatively, the filters can be controlled by the Feedback Destroyer - Frequency range: 20 Hz to 20 kHz - Frequency adjustment in increments of 1/60 octave - Bandwidth: 1/60 to 2 octaves, adjustable in 1/60-octave increments - Control range: +16 to -48 dB - Level adjustment resolution: 0.5 dB Feedback Destroyer (FB D) - Digital signal analysis for detecting feedback - Three independent digital notch filters per channel - Filters can be permanently programmed or used as automatic feedback suppression - Frequency range: 20 Hz to 20 kHz, in 1/60-octave increments - Filter bandwidth: 1/60 to 4/60 octaves, depending on the feedback characteristics - Control range: up to -48 dB, depending on the strength of the feedback - Typical suppression time: 0.5 s at 1 kHz Digital Delay - Digital stereo delay - Maximum delay time: 2.5 s - Independently adjustable for each channel - Smallest resolution: 0.1 ms - Display units: seconds, meters or feet Level Meter - Digital level meter with simultaneous graphical display of Peak and RMS values - RMS Attack/Decay: 60 dB/s - Peak Attack: 1 Sample - Peak Decay: 20 dB/s Noise Gate - Digital IRC (Interactive Ratio Control) - Threshold: -44 to -96 dB, adjustable in 1-dB increments - Attack and Release are processor-controlled and defined according to the program Limiter - Digital IGC (Interactive Gain Control) - Threshold: 0 to -36 dB, adjustable in 1-dB increments - Release: 500 to 5000 ms, adjustable in 250-ms increments Real Time Analyzer - Digital third-octave analyzer - Frequency range: 20 Hz to 20 kHz in 31 third-octave bands according to standardized ISO frequencies - Detectors: Peak or RMS - Decay times: 1 s, 250 ms, 65 ms or 15 ms, each for 20 dB Sine Generator - Frequency adjustment from 20 Hz to 20 kHz in increments of 1/60 octave - Level: 0 to -48 dB, adjustable in 0.5-dB increments Noise Generator - Choice of white or pink noise - Level range: 0 to -48 dB - Adjustment increments: 0.5 dB Display - 240 × 64 dot-matrix LC display - LED array for backlighting - Contrast adjustable in 32 steps Memory Options - 100 EQ program memories - Each program contains all settings for GEQ, PEQ, FB D and Delay, as well as a twelve-character alphanumeric name - Ten memory locations for RTA measurements - Two-level password protection - Memory-Protect and Security-Lock are each secured by a twelve-character alphanumeric password Power Supply - USA/Canada: 120 V~, 60 Hz - United Kingdom/Australia: 240 V~, 50 Hz - Europe: 230 V~, 50 Hz - Export model: 100–120 V~ or 200–240 V~, 50–60 Hz - Maximum power consumption: 30 W - Fuse at 100–120 V~: T 630 mA H - Fuse at 200–240 V~: T 315 mA H - Mains connection: standard IEC appliance socket - Battery: Lithium CR2032, 3 V, 180 mAh - Battery life: approximately 3 years Dimensions and Weight - Dimensions (H × W × D): 3 1/2" (89 mm) × 19" (482.6 mm) × 12" (304.8 mm) - Weight: approx. 5 kg - Shipping weight: approx. 6.6 kg Errors in price, images and item description, as well as interim availability, reserved. The unit can be tested on site. The sale is made excluding statutory liability for defects and warranty.

Specifications